DarwinFPV "Cement" Ultra Durable F7-100A Waterproof Stack

Specifications: 

FC : 

MCU: STM32F722
Gyroscope: MPU6000/ICM42688
OSD: AT7456E
Black box: Built-in 8G SD card
BEC output: 10V/3A 5V/3A
Reserved interface: 5x Uarts(1,2,3,4,6), 4x Softserial, 1x I2C, 4x RGB, 1x Buzzer, 1x USER(C09)
Input voltage: 2-6S Lipo
Firmware name: DARWINF722HDV2
Mounting hole: 30.5mm x 30.5mm
Dimensions: 39.5mm x 39.5mm x 4mm
Weight: 10.1g±0.2g

ESC: 

MCU: 32-bit F4 120MHz main frequency, maximum support 128KHz PWM Packet Rate
Continuous / peak current: 100Ax4/120Ax4 (continuous 100A requires water cooling environment)
Input voltage: 3-6S Lipo
Support throttle signal: Dshot150/300/600/1200 MultiShot Oneshot42 Oneshot125
Current sensor: support (current meter scale: 125)
Firmware name: DARWIN_F4_60
Power cord: 14AWG-120mm long (the ESC terminal and electrolytic capacitor have been welded at the factory)
Power plug: XT60
Dimensions: 36.8mm x 42.5mm x 7.5mm
Mounting hole: 30.5mm x 30.5mm
Weight: 23.0g±0.2g (excluding capacitors and power cords)
Apply for: 5-10 inch FPV Drones

Packing list: 

FC: 

• 1 x DarwinFPV "Cement" Ultra Durable F7 Waterproof Flight Controller

• 1 x 30mm ESC cable (8P)

• 1 x 65mm analog VTX cable (4P)

• 1 x 65mm GPS cable (6P)

• 1 x 65mm receiver cable (4P)

• 1 x 65mm HD VTX cable (6P)

• 4 x M3*4.5mm shock-absorbing balls (installed on FC)

• 1 x sticker

ESC:

• 1 x DarwinFPV "Cement" Ultra Durable 100A Waterproof ESC
• 1 x 30mm ESC cable (8P)
• 1 x XT60
• 1 x 14AWMG power cable with a length of 120mm (soldered to the ESC)
• 1 x 35V/1000uF electrolytic capacitor (soldered to the ESC)
• 4 x M3*6.6mm shock-absorbing balls (installed on the ESC)
• 1 x sticker

Stack:

• 1 x DarwinFPV "Cement" Ultra Durable F7-100A Waterproof Stack

• 1 x 30mm ESC cable (8P)

• 1 x 65mm analog VTX cable (4P)

• 1 x 65mm GPS cable (6P)

• 1 x 65mm receiver cable (4P)

• 1 x 65mm HD VTX cable (6P)

• 1 x XT60

• 1 x 14AWMG power cable (length 120mm, soldered to the ESC)

• 1 x 35V/1000uF electrolytic capacitor (soldered to the ESC)

• 4 x M3*4.5mm shock-absorbing balls (installed on FC)

• 4 x M3*6.6mm shock-absorbing balls (installed on the ESC)

• 4 x M3*25 hexagon socket head black 304 screws (installed on the stack)

• 4 x M3 nylon nuts

• 1 x sticker